Search results

Hey guys, still chasing down my boost issue. I was running the 101 5/8 gates on the 4th hole to the passenger side and was making 10-15lbs of boost. It was very inconsistent so I switched to a 100 1/2 gates and it made it worse. It only made 5-7lbs. I swapped back to the 101 5/8 on the 4th hole...

I've been attempting to chase down the cause of only making about 5 lbs on a 3.6 pulley. Replaced the worm clamps with T-Bolts and leak tested. I threw on a 3.48 pulley and dynoed it. It only put out 550whp at 5.6 psi. I just removed the Maxflo Bypass valve and installed a Tial 50MM Q BOV (-2...

Hello everyone, My black stang is in need of a good cleaning and waxing. I've put this list together with the $17 Amazon foam gun. Any advice or suggestions on products? MIC498 - Chenille Microfiber Premium Wash Mitt MIC70101 - Glass and Window Waffle MIC721 - Miracle Dryer with solid...

I've had this sound before and tried many things to diagnose it but it went away before I could find it. Well, its back. I've taken the belt off, moved pulleys, re-torqued damper, ran engine without blower accessories and everything. I've got a feeling it's the A/C compressor but won't have the...

What's everyone doing with their rear end in the diff? I got a one wheel spin the other day at the strip, and I got a feeling it's not liking my BMR suspension and slicks. :headbang: Are you guys replacing the clutch packs with better ones? which ones? I want to stay with my 3.31 gear ratio.

I started my car up yesterday to hear this knocking sound. I shut it off, checked oil and went ahead and replaced SC oil since I'm around 5K miles on it. You can't hear the knock at the back of the engine and it sounds like it's coming from the bottom front of the engine. It DOESN'T increase or...

I'm thinking about buying a fire extinguisher and a bracket to install in the trunk, anyone have one? Not sure which brand to go with..

I'm at the crossroads.. 17x10 JMS wheels or 19x9.5 PP wheels with MT SS tires. The problem is, do I buy the 17" JMS and throw on MTSS for the track and DD my 19" with whatever tires I can find.. or throw the MTSS on my 19's and DD/track it? I've never been to the track with my 15, and I don't...

SAI LI'S NEW KIT IS DIFFERENT THAN THE ONE I INSTALLED.. It should still be the same guide, just different pumps. If you have any questions I'll try to help but you can contact Sai Li on facebook. He responds quickly. I will attach photos when I get home. Sai Li's Dual Fuel Pump Kit Lift the...

I installed Sai Li's fuel kit. I hooked the pumps up to the same wire I used for my BAP (purple with green line). It never turns off now, only when there's no power to the car. I remember reading somewhere that it's the way you wire it but can't find that thread anymore.

I was messing with the Launch Control on my car and noticed that after my FI install/tune, it won't hold a steady RPM. It revs up to set limit (3500), then revs to 3K, then back to 3500 and so on. I have never used it but just in case. Anyone else have this issue?

I was messing with the RPM Limiter on my car and noticed that after my FI install/tune, it won't hold a steady RPM. It revs up to set limit (3500), then revs to 3K, then back to 3500 and so on. I have never used it but just in case. Anyone else have this issue?

I'm building an TT engine with a friend with 1000WHP as the goal. Do you think a 15 stock block with upgraded rods/Pistons will do the job? He has MPR on hold for a longblock at $16K but I feel we could save money with the new coyote engine.

Brand New Bobs Oil Separator - Flat Black - Vibrant Male to 45 Hose fitting - 6+ Feet of Black Braided Fuel Hose Tampa, FL $150

I see the $340 UPR catch can, but have a Bobs sitting in my toolbox. How can I plumb this in? What setup are you guys running with your Paxton?

Anyone running the MT Street Comps? I'm looking at buying a pair for the rear for some better traction.

My Paxton is almost fully tuned, and I already can't deal with the max-flow race bypass. I love the sound when you're in boost, but I can't deal with the constant hissing. What have you guys switched over to? I see someone did a Tial BOV by cutting off the flange and welding that shut, then...

I love my exhaust setup. I get thumb ups from everyone but it's just way too loud for work and starting it up at 5 AM. I have Stainless Power LT headers with no cats, an h pipe to magnaflow comp mufflers. I switched out to the stock resonator with stock mufflers and that's way too quiet. It...

I've searched this forum and google. I have found a few guides but most based off the 11-14 GT. For the 15+, should the RH cam be at 12 and the LH cam be at 5?